A. F. Bingöl and R. Gül, Residual bond strength between steel bars and concrete after elevated temperatures, Fire Safety Journal, vol.44, pp.854-859, 2009.

R. Eligehausen, I. Hofacker, and S. Lettow, Fastening Technique-Current Status and Future Trends, Symposium on Connections between Steel and Concrete, 55th RILEM Annual week, pp.1-17, 2001.

R. Cook, Behavior of Chemically Bonded Anchors, Journal of Structural Engineering, vol.119, issue.9, pp.2744-2762, 1993.

D. Van-gemart, Force transfer in epoxy bonded steel/concrete joints, Int Adhes Adhes, vol.1, issue.2, pp.67-72, 1980.

N. Pinoteau, P. Pimienta, T. Guillet, P. Rivillion, and S. Rémond, Effect of heating rate on bond failure of rebars into concrete using polymer adhesives to simulate exposure to fire, Int Adhes Adhes, vol.31, issue.8, pp.851-861, 2011.

H. Sato, K. Fujikake, and S. Mindess, Study on dynamic pullout strength of anchors based on failure modes, 13th World Conference on Earthquake Engineering, vol.854, 2004.

B. C. Vancouver and . Canada,

T. Bickel and A. Shaikh, Shear Strength of Adhesive Anchors, Precast Concrete Institute Journal, pp.92-100, 2002.

, Design Procedures for Concrete Anchors (Mechanical Expansion and Bonded Anchors), Michigan Transpostation Commission, 1998.

, Grout Bonded Concrete Anchors, 2011.

P. Bardonnet, Résines époxydes (EP) -Composants et propriétés, Traité plastiques et composites, éditions T.I. (Techniques de l'ingénieur, 1992.

K. Benzarti, N. Houhou, M. Quiertant, and S. Chataignier, Creep behavior of cold curing epoxy adhesives: analysis and predictive approach, Composites In Civil Engineering (CICE), 2014.
URL : https://hal.archives-ouvertes.fr/hal-01207683

H. Spieth, J. Ozbolt, A. Eligehausen, and J. , Numerical and experimental analysis of postinstalled rebars spliced with cast-in-place rebars, International Symposium on Connections between Steel and Concrete, vol.889, 2001.

B. Rosca and Z. Kiss, Bond behaviour of the post-installed bundled rebars anchors with cement mortar in hardened concrete, Gheorghe asachi" din Iasi, vol.LXI, pp.117-129, 2015.

A. Colak, Parametric study of factors affecting the pull-out strength of steel rods bonded into precast concrete panels, Int Adhes Adhes, vol.21, issue.6, pp.489-493, 2001.

A. Colak, Estimation of ultimate tension load of methylmethacrylate bonded steel rods into concrete, Int Adhes Adhes, vol.27, issue.8, pp.653-660, 2007.

E. Nigro, A. Bilotta, G. Cefarelli, G. Manfredi, and E. Cosenza, Performance under fire situations of concrete members reinforced with FRP rods: Bond models and design nomograms, Jornal of composites for construction, vol.16, issue.4, pp.395-406, 2012.

M. Bajer and J. Barnat, Dependence of Ultimate Bond Stress on Bond Anchor Carrying Capacity, Slovak Journal of Civil Engineering, pp.1-7, 2009.

J. Meszaros and R. Eligehausen, Einfluss der Bohrlochereiningung und vo feuchtem Beton auf das Tragvehalten von ijektions düblen (Influence of hole cleaning and of humid concrete on the load bearing behaviour of injection anchors), 1998.

H. Spieth and R. Eligehausen, Bewehrungsnschlüsse mit nachträglich eingemöelten bewehrungstaben (Starter bars with post installed rebars), Beton und Stahlebetonbau, vol.97, issue.9, pp.445-459, 2002.

R. Eligehausen and F. Werner, Recent Developments and Open Problems in Fastening Technique, 2nd International Symposium on Connections between Steel and Concrete, 2007.

J. Petit, V. Nassiet, Y. H. -r, and . Baziard, Etude de la durabilité des assemblages collés, p.160, 2005.

Y. Zhang, G. Lou, K. Chen, and G. Li, Residual strength of organic anchorage adhesive for post-installed rebar at elevated temperatures and after heating, Fire Technology Journal, vol.52, pp.877-895, 2016.

M. Lahouar, J. Caron, N. Pinoteau, G. Forêt, and K. Benzarti, Mechanical behavior changes of chemical anchors under high temperature exposure: Experimental investigation, International journal of adhesion and adhesives, vol.78, pp.200-211, 2017.

J. Reis, Effect of Temperature on the Mechanical Properties of Polymer Mortars, Materials Research, vol.15, issue.4, pp.645-649, 2012.

R. Adams, J. Coppendale, V. Mallick, and H. Al-hamdan, The effect of temperature on the strength of adhesive joints, International Journal of Adhesion and Adhesives, vol.12, issue.3, pp.185-190, 1992.

N. Pinoteau, J. Heck, R. Avnel, P. Pimienta, T. Guillet et al., Prediction of failure of a cantilever-wall connection using post-installed rebars under thermal loading, Engineering structures, vol.56, pp.1607-1619, 2013.

N. Pinoteau, Comportement des Scellements Chimiques d'Armaturesraportées pour Béton en Situation d'Incendie, 2013.

U. Sorathia, R. Lyon, R. Gann, and L. Gritzo, Materials and fire threat, Fire technology journal, vol.33, issue.3, pp.260-275, 1997.

, EN 1992-1-1, Eurocode 2: Design of concrete structures -part 1-1: General rules and rules for buildings, 2004.

&. Eota and . Etag, European Techniques of Anchor Guideline, 2001.

. Aci-provisional and . Standards, ACI 335.2-01, Evaluating the performance of post-installed mechanical anchors in concrete, 2001.

. Astm-international, ASTM C881: Standard specification for epoxy-resin base bonding systems for concrete, 2013.

C. B. Press, GB 50367-2006: Design code for strengthening concrete structure, 2006.

R. Eligehausen and J. Asmus, Expert report -Design of post-installed rebars with injection mortarFIS EM under fire exposure up to 240 min, 2008.

, EAD 330087-00-0601, Systems for post-installed rebar connections with mortar, 2015.

, EN 1992-1-2 Eurocode 2. Part 1-2: Design of concrete structures -General rulesStructural fire design, 2005.

M. Van-schilfgaarde, A. Abrikosov, J. , and B. , Origin of the Invar effect in iron-nickel alloys, Nature, vol.400, pp.46-49, 1999.